NUJNO za Klemnaxx !!!
Klemenxx!
Nakdnadno sem izvedel, da je bila na Win XP, ki so na drugem disku (Disk C) včeraj istalairana Kazaa Desktop 2.1. Tudi po odstranitvi tega programa XP-ji na drugem disku še vedno javijo enako napako, po kateri se takoj resetirajo.
Razberem lahko le, da Register nečesa ne uspe naložiti… in spodaj napaka z virtual memory dump, nekaj takega.
Ali obstajata možnosti za restore registra iz drugih windowsov ali s pomočjo instalac. cd-ja (Opcija Recover mode?)?
Vnaprej hvala za nasvet
lp marjan
Navodila za popravilo windows xp, če se ne žaženejo več:
Cannot Start Windows XP if the System or Software Hive Is Missing or
Damaged (Q303012)
SYMPTOMS
When you try to start or restart your Windows XP-based computer, you may
receive one of the following error messages:
Windows XP could not start because the following file is missing or
corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM
Windows XP could not start because the following file is missing or
corrupt: \WINDOWS\SYSTEM32\CONFIG\SOFTWARE
Stop: c0000218 {Registry File Failure} The registry cannot load the hive
(file): \SystemRoot\System32\Config\SOFTWARE or its log or alternate
CAUSE
This issue can occur if the System or Software hive for the Windows XP
installation is missing or damaged.
RESOLUTION
To resolve this issue, use one of the following methods.
Use the Recovery Console Tool
To restore a damaged registry hive, use the Recovery Console to restore
the backup copy of the hive from the Repair folder. The Repair folder
contains a copy of the system’s registry hives that were created after
the first successful startup of Windows XP.
WARNING : Although data should not be affected by the following
procedure, you may need to restore changes you previously made to
programs or system settings since the first time you successfully
started Windows XP.
To replace the damaged registry hive and restore the backup copy of the
hive from the Repair folder: Start your computer to the Recovery
Console.
Determine if the file that is mentioned in the “Symptoms” section of
this article is present, and if it is, rename it:
In Recovery Console, change to the c:\Windows folder.
Type cd sytem32\config , and then press ENTER.
Type dir system , and then press ENTER.
If you cannot run the preceding command successfully (because the file
is missing), skip to step 3. If you can run the preceding command
successfully, type ren system system.bak , and then press ENTER.
NOTE : If the message that you received referred to the software file,
replace “system” with “software” in the preceding command. For example,
you would type ren software software.bak (instead of ren system
system.bak ), and then press ENTER.
Type copy c:\windows\repair\system , and then press ENTER.
NOTE : If the message that you received referred to the software file,
replace “system” with “software” in the preceding command. For example,
you would type copy c:\windows\repair\software (instead of copy
c:\windows\repair\system ), and then press ENTER. You should receive a
“One file copied” informational message. For additional information
about how to use Recovery Console during startup, click the article
number below to view the article in the Microsoft Knowledge Base:
Q307654 HOW TO: Install and Use the Recovery Console for Windows XP
IMPORTANT : If you encounter problems when you run the preceding
commands, you may need to use the Change Directory command ( cd ) one
folder at a time before you run the preceding commands. For example,
type cd system32 , press ENTER, type cd config , and then press ENTER.
Type exit , and then press ENTER to quit Recovery Console and restart
the computer.
You Cannot Start from the Windows XP CD-ROM or Use Recovery Console
If you cannot start from the Windows XP CD-ROM or use Recovery Console
and you are using the FAT file system (not the NTFS file system):
Use a startup disk from one of the following operating systems to start
your computer to a command prompt:
lp
Forum je zaprt za komentiranje.